Sherline Direct Cart items: 0  Total: $0.00
 
Monthly Special for October 2017
Monthly Special for October 2017

Product #: 2255/2258/2261/2272/7605B/7608B

[Add to Wishlist]

Quantity:
In stock

Internet Special for October 2017

Save 20% on your choice of 3/8" Carbide Inserted Tip Cutting Tools and Inserts

These carbide tool holders and boring bars are offered as sets to complement our new front side and rear side multi-tool holders. The front-side tool holder (P/N 5932) holds up to two, round boring tools, and a slot for holding turning, grooving or threading tools. The rear-side cutoff tool holder (P/N 5931) is similar to the front-side tool holder, but it has a slot for holding a cutoff tool blade (P/N 30860). Using the holder as a rear mounted cutoff tool allows you to use the cutoff tool from the back side of the part.

All of these tool holders can also be used in conjunction with our 3/8" Insert Holder Tool Post (P/N 7600) and the boring bars can be used with the Rear Mount Cutoff Tool and Holder (P/N 3018)

We are also offering our bulk packs of 10 carbide inserts (see below for details). Carbide cutters give good finishes on hard-to-machine materials such as cold rolled steel. They will also work on aluminum, brass or leaded steels, and will last practically forever.

 

 

 

RH and LH 80° Carbide Insert Holders

P/N 2255 Regularly $84, Save $16.80, Now $67.20

Each comes with a P/N 7608 80° carbide insert, hold-down screw and special Torx key. The 5° offset angle of the tip makes it easier to accomplish certain cuts. For example, by using the tool holder square with the crosslide, you can turn an O.D. up to a shoulder and then finish the shoulder by backing the tool out while still maintaining the proper tool clearance. The tip of the cutting tool is .375″ from the bottom of the holder, which is the industry standard. The holders are made from case hardened steel with a black oxide finish. The 80° inserts are generally used for roughing cuts.

2258_Carbide-Insert-Tool-Holders

55° Carbide Insert Holders

P/N 2258 Regularly $73.50, Save $14.70, Now only $58.80

Each comes with a P/N 7605 55° carbide insert, hold-down screw and special Torx key. The 5° offset angle of the tip makes it easier to accomplish certain cuts. For example, by using the tool holder square with the crosslide, you can turn an O.D. up to a shoulder and then finish the shoulder by backing the tool out while still maintaining the proper tool clearance. The tip of the cutting tool is .375" from the bottom of the holder, which is the industry standard. The holders are made from case hardened steel with a black oxide finish.

2261_Inserted-Tip-Carb-Boring-Bars

RH 55° & 80° Boring tools

P/N 2261 Regularly $99.75, Save $19.95, Now only $79.80

These 3/8″ diameter boring bars hold a carbide insert secured with a Torx screw.  Each comes with either a 2-sided  55° or 80° carbide insert and Torx wrench. The 55° RH boring tool will fit into a 3/4″ starting hole. The 80° holder will fit into a smaller 1/2″ hole. The 80° holder offers a little more strength for roughing cuts while the 55° insert will cut into sharper corners. The 3-1/4″ long holder can bore a hole a little over 2″ deep with two fastening screws tightened on it. The holders are made from 1144 Stressproof steel with a black oxide finish. Available individually, or as a pair at a substantial cost savings.

LH 55° & 80° Boring tools

P/N 2272 Regularly $99.75, Save $19.95, Now only $79.80

Each boring tool comes with a carbide insert, hold-down screw and special Torx key.  The 55° RH boring tool will fit into a 3/4″ starting hole. The 80° holder will fit into a smaller 1/2″ hole. In addition to fitting into a smaller hole, the 80° insert offers a little more strength, while the 55° insert will cut into a sharper corner. The holders are made from case hardened steel with a black oxide finish. A flat is ground on one side so the two hold-down screws of the 7600 tool post can tighten against it to keep the tool from rotating.

Download PDF 2261 & 2272 Instructions

Instructions PDF Download

Carbide Insert for 55° Holder (bulk 10)

P/N 7605B Regularly $110.25, Save $22.05, Now only $88.20

Carbide Insert for 80° Holder (bulk 10)

P/N 7608B Regularly $94.25, Save $18.85, Now only $75.40

Though not inexpensive, when you consider you are getting four cutting tools in one and are saving a lot of time in tool sharpening, it is really a pretty good deal.

Carbide cutters give good finishes on hard-to-machine materials such as cold rolled steel. They will also work on aluminum, brass or leaded steels, and will last practically forever, however, the best finishes on those materials are still achieved with a good, sharp high-speed steel tool.

Download PDF Carbide Tip Tools Instructions

Instructions PDF Download

NOTE: In the event we run out of a product offered on special, we may change the special or put the items on back order at our discretion.




May we also suggest
Front Side Multi-Tool Holder - 3/8
Front Side Multi-Tool Holder - 3/8"
Rear Side Cutoff Multi-Tool Holder - 3/8
Rear Side Cutoff Multi-Tool Holder - 3/8"
3/8
3/8" Insert Holder Tool Post


 

Site Map